The American Architectural Manufacturers Association (AAMA) released AAMA , a voluntary specification for field testing of newly. Newly Installed Fenestration Products” and. AAMA , “Voluntary Specification for Field Testing of Newly Installed. Storefronts, Curtain Walls and Sloped. AAMA and documents, designed for field testing of newly installed fenestration products. The aforementioned. AAMA documents were often.
|Genre:||Health and Food|
|Published (Last):||21 June 2017|
|PDF File Size:||20.86 Mb|
|ePub File Size:||19.79 Mb|
|Price:||Free* [*Free Regsitration Required]|
Conducting the investigative testing to verify and extend hypotheses arrived at during aa,a document review and inspection portions of the investigation using controlled and reproducible procedures.
ASTM states the field test may also be made after the building is completed and in service to determine whether or not reported leakage problems are due to the failure of the installed assemblies.
The main objective of forensic water testing is to identify the leak paths through the simulation of the weather events that produced the reported leakage. The AAMA describes steps for calculating the approximate differential air pressures the specimens experienced during actual wind driven rain events. Procedure A is a uniform static air pressure difference. This test method exclusively utilizes a uniform static air pressure difference.
Analyzing the data and establishing a cause and effect relationship between wall characteristics and the observed leakage. The AAMA was first released in and has had many changes over the years. Voluntary Specification for Field Testing of Newly Installed Storefronts, Curtain Walls and Sloped Glazing Systems This specification establishes the requirements for test specimens, apparatus, sampling, test procedures and test reports to be used in evaluating the performance of newly installed storefronts, curtain walls and zama glazing systems.
The reviewing of 50308 documents for the building. The AAMA is the proper test method for field testing of storefronts, curtain walls and sloped glazing for air leakage and water penetration resistance performance.
There are no previous editions. SITC utilizes the AAMA when conducting forensic water spray testing on windows, doors, curtain walls, storefronts, slope glazing systems and exterior walls. This standard is utilized for laboratory or interior mock up testing only. There are two aamaa procedures listed for the test method.
Specifically excluded from this field check method is the testing of operable components such as operable window and doors. These systems shall be tested per the AAMA The diagnostic field water check is utilized for installed storefronts, curtain walls and sloped glazing systems only.
This field water check method is not intended to test the rated or specified water performance representative of a wind driven rain event. This specification is for quality assurance testing only. This specification is for quality assurance testing only of storefronts, curtain walls and sloped glazing systems and their installation.
The determination of the service history of the building to provide patterns in the observed leakage and visible damage and where to focus our investigation. The objective of forensic water spray testing is to identify and track the water migration through the simulation of wind driven rain events. The most current edition is the AAMA Member discount will be reflected after successful login to the Checkout process. This field check procedure is only intended to evaluate joints, gaskets and sealant details in the glazing which are designed to remain permanently closed and water tight.
Procedure B is a cyclic static air pressure difference. The AAMA is the proper test method for field testing of storefronts, curtain walls and sloped glazing for air leakage resistance and water penetration resistance performance.
SITC utilizes isolation techniques to assist in identifying the source or sources of the reported water leakage. This differs greatly from the AAMA and AAMA field testing procedures that are intended for evaluating newly installed fenestration products or quality assurance testing.
AAMA Water Spray Testing
This specification is for quality assurance water penetration testing only. The testing procedure outlined in the AAMA This starts with a clearly defined sequence of activities that SITC follows during a investigation: American Architectural Manufacturers Association. The AAMA is the first edition of this voluntary guideline.
Read more about what our customers have to say This specification establishes the requirements for test specimens, apparatus, sampling, test procedures and test reports to be used in evaluating the performance of newly installed storefronts, curtain walls and sloped glazing systems. See our AAMA page for additional information if your project requires to test for the rated air leakage or rated water penetration performance. Please read our simple purchasing instructions first to ensure a smooth transaction.
This standard is utilized for either field quality assurance testing or forensic testing. It aamx only be utilized prior to the issuance of the building occupancy permit and no later than six months after the installation of the fenestration product. This specification provides aams guide which can be used to evaluate the installed performance of storefronts, curtain walls and sloped glazing systems for resistance to water penetration under controllable and reproducible wind driven rain conditions.
The evaluation of the design concept to determine if any water 5503-08 performance requirements were specified for the wall. 053-08 specification is for quality assurance water penetration testing only. See our AAMA page for additional information.
AAMA Combined Air & Water Testing | BETechnologies Ireland
Specifically excluded from this specification are aamma, glass doors and skylights. ASTM states that the field test may be made at the time the window, skylight, curtain wall or door assemblies are initially installed.
This field check is not appropriate for testing operable components.