ADAQ datasheet, ADAQ circuit, ADAQ data sheet: AD – Ultralow Drift Op Amp,alldatasheet, datasheet, Datasheet search site for Electronic. ADA Datasheet, ADA PDF, ADA Data sheet, ADA manual, ADA pdf, ADA, datenblatt, Electronics ADA, alldatasheet, free, datasheet. ADA datasheet, cross reference, circuit and application notes in pdf format.
|Published (Last):||1 April 2009|
|PDF File Size:||1.53 Mb|
|ePub File Size:||12.61 Mb|
|Price:||Free* [*Free Regsitration Required]|
When they are on, each switch conducts equally well in both directions and has an input signal range that extends to the power supplies. This yields performance that can be used to implement high accuracy systems, even in single-supply designs. It provides a high precision, fully integrated, low cost single-chip solution for generating current loop signals in a compact pin SOIC or PDIP package. Stability while driving capacitive loads is another benefit of this design over CMOS rail-to-rail amplifiers.
Applications Battery-operated instrumentation Servo amplifiers Actuator drives Sensor conditioners Power supply control. High switching speed also makes the device suitable for video signal switching. Each switch conducts equally well in both directions when ON and each has an input signal range that extends to the supplies.
The only external components that are required in addition to normal transient protection circuitry are three low cost capacitors which are used in the DAC output filter. This is useful for driving coax cable or large FET transistors.
ADAQ Datasheet pdf – Ultralow Drift Op Amp – Analog Devices
These switches also feature high switching speeds and low RON. Analog Devices also offers over 30 other high speed amplifiers from the low noise AD 1.
The devices datashert operate comfortably anywhere in catasheet In the off condition, signal levels up to the supplies are blocked. To provide flexibility to the system designer, the AD can be operated in either latched or transparent mode. A guaranteed maximum input offset voltage of 0.
These devices perform the same electronic adjustment function as a potentiometer or variable resistor. If you have questions or suggestions,please leave us a message,we will reply you as soon da707aq we can!
If the AD is going to be used at extreme temperatures and supply voltages, an external output transistor can be used to minimize power dissipation on the chip via the “BOOST” pin.
The FET-input stage results in a low bias current of 50 pA. In addition, the AD provides excellent dc precision. A serial data output pin at the opposite end of the serial register AD only allows simple daisy chaining in multiple VR applications without requiring additional external decoding logic. Home Products News contact. The ADGA switches one of 16 inputs to a common output, depending on the state of four binary addresses and an enable input.
For applications such as transformers that require driving inductive loads, increases in efficiency are also possible. For applications in which the analog signal is unipolar, the ADGA can be operated from a single rail power supply.
This multiplexer also features high switching speeds and low RON. It can be used in three-wire or asynchronous mode and a serial-out pin is provided to allow daisy chaining of multiple DACs on the current loop side of the isolation barrier.
Each VR has its own VR latch that holds its programmed resistance value. Low charge inject is inherent in the design.
The resistance between the wiper and either endpoint of the fixed resistor varies linearly with respect to the digital code transferred into the VR latch. Common-mode rejection datasheeet a minimum of 78 dB.
The small signal bandwidth is kHz at a gain of Applications Audio and video switching Battery-powered systems Test equipment Communication systems. These VR latches are updated from an internal serial-to-parallel shift register that is loaded from a standard 3-wire serial-input digital interface.
All switches exhibit break-before-make switching action for use in multiplexer applications. The variable resistor offers a completely programmable value of resistance between the A terminal and the wiper or the B terminal and the wiper.
By using a bipolar front end, lower noise and higher accuracy af707aq those of CMOS designs have been achieved. For users of 3. Inherent in the design is low charge injection for minimum transients when switching the digital inputs.
Low gain error and low nonlinearity make the AD ideal for precision instrumentation applications requiring datashheet gain. The first three bits are decoded to determine which VR latch is loaded with the last eight bits of the data-word when the CS strobe is returned to logic high. The on-resistance profile is very flat over the full analog input range, ensuring good linearity and low distortion when switching audio signals. Product Highlights Extended signal range.
This allows designs to achieve higher efficiencies and to transfer more power to the load than previously possible without the use of discrete components. CMOS construction ensures ultralow power dissipation, making the device ideally suited for portable, battery-powered instruments.
The device is fully specified with a single 12 V supply. Eleven data bits make up the data-word clocked into the serial input register. The ADGA switches are turned on with a logic low on the appropriate control input. It is complete, including amplifier, resistor network and TTL-compatible latched inputs, and requires no external components.
Ad707qa Mechanical potentiometer replacement Instrumentation: